The WaterCop automatic shutoff valve installs on the main water line near the existing manual shut-off valve. WaterCop flood sensors install near water using appliances and in rooms where running water is present. Each WaterCop Classic system can support an unlimited number of water and low temperature sensors. When leaking water comes in contact with any of the sensors, a wireless signal is immediately broadcast to the WaterCop main valve causing the valve to close. Water flow is quickly cutoff to all areas of the home and any continuous flooding is stopped.
WaterCop Classic 1.25 In. Lead Free Ball Valve with Actuator, 3 Sensors
New WaterCop Electric Actuator Motor, 115VAC (1/2 through 1-1/14 inch) WCDACT1New WaterCop Electric Actuator Motor, 115VAC (1/2 through 1-1/14 inch) WCDACT1
Water Cop Electric Actuator for All WaterCop Valves .5 inches Valves to 1.25 Inches WCDACT electric actuator with alarm interface, internal antenna and built in I/O port and easy shut off buttons. Watercop motorized water valve actuator only: No valve included. Actuator interfaces with a 1/2 inch, 3/4 inch or 1 inch " Water Cop Ready" brass ball water valve . No valves nor moisture sensors are included with the actuator. Red button turns off water flow. Push green button and valve is opened. 8 ft cord. Water Cop Electric Actuator for Dynaquip Water Valve: Fully automatic: use electricity or batteries. Compatible with .5, .75, 1 inch and 1.25 inch Dynaquip lead free full port brass ball valves (Not Included) Security system interface. Built-in I/O port with RJ45 connection. Watercop moisture sensors and low temperature sensors sold separately. Low voltage interface terminal direct wires to home security alarm system or home automation control panel. For security systems with auxiliary outputs, contact security system dealer/installer for interface installation. 5 VDC output available from the WaterCop. Frequency: 418 MHz Wireless Range: approx. 100 to 200 feet Ambient Temperature: 35 degrees to 105 degreesF Enclosure: Polycarbonate Voltage: 12VDC, 60 Hz Power Cord: 20 feet. Approvals: FCC, UL Warranty: 2 Years Made in USA by Dynaquip Controls.
WaterCop Power Adapter for Flood/Temp Sensors (WPA)WaterCop Power Adapter for Flood/Temp Sensors (WPA)
Power your WaterCop Classic flood and temperature sensor by plugging them in with the WaterCop Power Adapter for Flood/Temp Sensors. This optional power adapter wires into the sensor and plugs into a standard outlet, eliminating the need for batteries. It works with sensor models WCDFS1, WCFS2, and WCDFST (those with an internal antenna). NOTE: Not intended for use with older sensor models WH100, WH200, and FH100 (with external antennas). To power these sensors, purchase the older power adapter model ACA100.
WaterCop Classic Motorized Actuator W/Lead Free Water Valve, 1.25 In.WaterCop Classic Motorized Actuator W/Lead Free Water Valve, 1.25 In.
Water Valve Actuator for 1.25 Inch Water Lines Includes Lead Free Ball Valve WaterCop automatic water shut-off valve device by Dynaquip is an industrial quality, electrically automated full port brass ball valve that meets VT and CA standards for potable water systems. This Water Cop device features a "direct mount" actuator mounting for precision automation. Install this Water Cop actuator on the incoming main water supply line within a home or business. Push the red button to shut off water; push the green button to turn it on. Requires 115VAC current to operate. Or add a battery back-up in case of a power failure. What does lead free mean with regard to water valves? Lead Free NSF61G refers to the wetted surface of pipe, fittings and fixtures in potable water systems that have a weighted average lead content = 0.25% Source: California Health & Safety Code (116875); Vermont Act 193. California Assembly Bill 1953 and Vermont Act 193 reduced the amount of lead in specific plumbing fixtures from its current amount of no more than 8% to a new standard not to exceed 0.25%. All fifty states must comply with this NEW 0.25% requirement by January 4, 2014. The WaterCop automatic water valve device includes a security system alarm interface and a 1.25 Inch brass ball valve that meets low lead standards for drinking water. The WaterCop actuator's integrated 418MHz radio frequency receiver chip set has user adjustable digital security codes, which allows nearby Water Cop systems to operate independently. This unit features auxiliary low voltage contacts with modular RJ-45 interface socket for simplified connection to optional WaterCop accessories — or integrate with a third-party home security or home automation system using standard Cat-5 computer cabling. Low voltage interface terminal direct wires to home security alarm system or home automation control panel. For security systems with auxiliary outputs, contact security system dealer/installer for interface