WaterCop Flood Sensor with Single Sensor Paired with WaterCop Shuts Off Water Valve Replaces WH-100. Made in USA. WCDFS1 water alarm detects moisture with single probe moisture sensor . Power: two AA batteries or hard-wire a 120VAC adapter. Internal radio transmission antenna communicates with WaterCop if installed. Water sensor alarm intensity similar to watch alarm or pager beep when probe detects moisture. WaterCop , if installed, shuts off WaterCop protected water valve. Internal 418 MHz radio transmitter chip set has up to a 200 foot operating range. Moisture sensor has user adjustable digital security codes. Low battery warning chirp. 3 VDC. 10 mA. Compatible with older and new classic systems. 6 foot water sensor cord. Indoor use only. Note: Safe Home does not recommend using this unit as a local stand-alone alarm as it is not loud . It is meant to work with the Water Cop unit.
WaterCop Flood Sensor Single Probe
Related Post
WaterCop Flood Sensor Dual ProbeWaterCop Flood Sensor Dual Probe
Monitor specific leak prone areas within the home for unwanted and potentially damaging water accumulation of internal flooding. Flood sensors feature a robust 418MHz radio transmitter chipset with up to a 200 foot operating range, user adjustable digital security codes, and operate on either two (2) AA batteries or an optional AC power adapter. Low battery warning chirp. Sensors are equipped with two (2) sensor probes with 6 foot sensor cords each. When leaking water comes in contact with either sensing probe the Water Sensor sends a radio signal to the WaterCop "on duty" telling it to shut off the main water supply. Each WaterCop can support an unlimited number of Water Sensors.
WaterCop Classic 1.25 In. Lead Free Ball Valve with Actuator, 3 SensorsWaterCop Classic 1.25 In. Lead Free Ball Valve with Actuator, 3 Sensors
The WaterCop automatic shutoff valve installs on the main water line near the existing manual shut-off valve. WaterCop flood sensors install near water using appliances and in rooms where running water is present. Each WaterCop Classic system can support an unlimited number of water and low temperature sensors. When leaking water comes in contact with any of the sensors, a wireless signal is immediately broadcast to the WaterCop main valve causing the valve to close. Water flow is quickly cutoff to all areas of the home and any continuous flooding is stopped.
New WaterCop Electric Actuator Motor, 115VAC (1/2 through 1-1/14 inch) WCDACT1New WaterCop Electric Actuator Motor, 115VAC (1/2 through 1-1/14 inch) WCDACT1
Water Cop Electric Actuator for All WaterCop Valves .5 inches Valves to 1.25 Inches WCDACT electric actuator with alarm interface, internal antenna and built in I/O port and easy shut off buttons. Watercop motorized water valve actuator only: No valve included. Actuator interfaces with a 1/2 inch, 3/4 inch or 1 inch " Water Cop Ready" brass ball water valve . No valves nor moisture sensors are included with the actuator. Red button turns off water flow. Push green button and valve is opened. 8 ft cord. Water Cop Electric Actuator for Dynaquip Water Valve: Fully automatic: use electricity or batteries. Compatible with .5, .75, 1 inch and 1.25 inch Dynaquip lead free full port brass ball valves (Not Included) Security system interface. Built-in I/O port with RJ45 connection. Watercop moisture sensors and low temperature sensors sold separately. Low voltage interface terminal direct wires to home security alarm system or home automation control panel. For security systems with auxiliary outputs, contact security system dealer/installer for interface installation. 5 VDC output available from the WaterCop. Frequency: 418 MHz Wireless Range: approx. 100 to 200 feet Ambient Temperature: 35 degrees to 105 degreesF Enclosure: Polycarbonate Voltage: 12VDC, 60 Hz Power Cord: 20 feet. Approvals: FCC, UL Warranty: 2 Years Made in USA by Dynaquip Controls.